2006 SeaDoo GTI (236A,236B,256A,256B) GTI SE (246A,246B) GTX (146A,146B) Supercharged (166A) Limited (186A,186B,186C) Wake (156A,156B) RXP (216A,216B,216C,216D) RXT (176A,176B,176C,176D) Service/Shop Manual
Free PDF download of the 2006 SeaDoo GTI (236A,236B,256A,256B) GTI SE (246A,246B) GTX (146A,146B) Supercharged (166A) Limited (186A,186B,186C) Wake (156A,156B) RXP (216A,216B,216C,216D) RXT (176A,176B,176C,176D) Service/Shop Manual: the factory shop manual, 403 pages (94.9 MB). Covers service, repair, adjustment and technical data, with the original illustrations and wiring diagrams where included.
- Year
- 2006
- Type
- Shop manual
- Pages
- 403
- File
- PDF, 94.9 MB
2006 SeaDoo GTI (236A,236B,256A,256B) GTI SE (246A,246B) GTX (146A,146B) Supercharged (166A) Limited (186A,186B,186C) Wake (156A,156B) RXP (216A,216B,216C,216D) RXT (176A,176B,176C,176D) Service/Shop Manual Contents
- SAFETY NOTICE
- INTRODUCTION
- GENERAL INFORMATION
- HULL IDENTIFICATION NUMBER (HIN)
- ENGINE IDENTIFICATION NUMBER (EIN)
- ARRANGEMENT OF THIS MANUAL, ILLUSTRATIONS AND PROCEDURE
- ENGINE EMISSIONS INFORMATION
- WORKING ON WATERCRAFT
- SELF-LOCKING FASTENERS PROCEDURE
- LOCTITE APPLICATION PROCEDURE
- TIGHTENING TORQUES
- 01MAINTENANCE
- 01- MAINTENANCE CHART
- 02- PRESEASON PREPARATION
- 03- STORAGE PROCEDURES
- PROPULSION SYSTEM
- FUEL SYSTEM
- ENGINE
- ELECTRICAL SYSTEM
- VEHICLE
- CHECKLIST
- 04- SPECIAL PROCEDURES
- TOWING THE WATERCRAFT IN WATER
- SUBMERGED WATERCRAFT
- WATER-FLOODED ENGINE
- 02TROUBLESHOOTING
- 01 - TROUBLESHOOTING CHART
- ENGINE
- STARTING SYSTEM
- ELECTRICAL SYSTEM
- PROPULSION
- STEERING SYSTEM
- 03ENGINE
- 01- ENGINE REMOVAL AND INSTALLATION
- GENERAL
- PROCEDURES
- ENGINE REMOVAL
- CLEANING
- INSTALLATION
- ENGINE ALIGNMENT
- 02- ENGINE LEAK TEST
- PREPARATION
- PROCEDURE
- 03- AIR INTAKE SYSTEM
- INSPECTION
- REMOVAL
- INSTALLATION
- 04- INTAKE MANIFOLD AND INTERCOOLER
- PROCEDURES
- INTAKE MANIFOLD
- INTERCOOLER
- 05- SUPERCHARGER
- INSPECTION (SUPERCHARGER INSTALLED)
- REMOVAL
- DISASSEMBLY
- PARTS INSPECTION
- ASSEMBLY
- INSTALLATION
- 06- EXHAUST SYSTEM
- GENERAL
- EXHAUST SYSTEM COOLING
- MAINTENANCE
- EXHAUST SYSTEM FLUSHING
- PROCEDURES
- EXHAUST PIPE
- EXHAUST MANIFOLD
- MUFFLER
- RESONATOR
- EXHAUST OUTLET
- 07- PTO HOUSING AND MAGNETO
- GENERAL
- PROCEDURES
- PTO HOUSING
- PTO SEAL
- COUPLING
- STATOR
- ROTOR AND TRIGGER WHEEL
- RING GEAR
- STARTER DRIVE
- OIL SPRAY NOZZLE
- 08- LUBRICATION SYSTEM
- MAINTENANCE
- OIL LEVEL VERIFICATION
- OIL CHANGE
- OIL FILTER
- INSPECTION
- ENGINE OIL PRESSURE
- PROCEDURES
- PTO OIL STRAINER
- SUCTION PUMP OIL STRAINER
- ENGINE OIL PRESSURE REGULATOR
- OIL PRESSURE PUMP
- OIL SUCTION PUMP
- OIL SEPARATOR COVER
- TOPS VALVE
- OIL COOLER
- 09- COOLING SYSTEM
- GENERAL
- CIRCUIT
- TECHNICAL SPECIFICATIONS
- INSPECTION
- PRESSURE CAP
- HOSES AND CLAMPS
- COOLING SYSTEM LEAK TEST
- MAINTENANCE
- COOLANT REPLACEMENT
- PROCEDURES
- CLAMPS
- WATER PUMP HOUSING
- WATER PUMP IMPELLER
- THERMOSTAT
- ROTARYSEAL
- 10- CYLINDER HEAD
- GENERAL
- PROCEDURES
- EXHAUST MANIFOLD
- VALVE COVER
- ROCKER ARM
- CAMSHAFT TIMING GEAR
- TIMING CHAIN
- CYLINDER HEAD
- CAMSHAFT
- VALVE SPRING
- VALVE
- 11- CYLINDER BLOCK
- GENERAL
- PROCEDURES
- TIMING CHAIN
- CHAIN TENSIONER
- PISTON/CONNECTING ROD
- PISTON RINGS
- CRANKSHAFT
- BALANCER SHAFT
- CYLINDER BLOCK
- 04ENGINE MANAGEMENT (1503 4-TEC)
- 01 - OVERVIEW
- GENERAL
- OPERATING PRINCIPLE
- AIR INDUCTION
- FUEL SYSTEM
- ELECTRICAL SYSTEM
- ENGINE MANAGEMENT SYSTEM
- ElECTRONIC FUEL INJECTION
- IGNITION SYSTEM
- ENGINE MODES OF OPERATION
- MONITORING SYSTEM
- DIAGNOSTIC MODE
- ENGINE MANAGEMENT SYSTEM DIAGRAM
- 02 - EMS DIAGNOSTIC AND COMMUNICATION TOOLS
- GENERAL
- DIAGNOSTIC
- MONITORING SYSTEM
- FAULT CODES
- COMMUNICATION TOOLS
- MPI MULTI-PURPOSE INTERFACE
- MPI-2 MULTI-PURPOSE INTERFACE)
- BUDS SOFTWARE
- 03- ADJUSTMENT AND REPAIR PROCEDURES
- GENERAL
- FUEL SYSTEM
- ELECTRICAL SYSTEM
- BASIC ADJUSTMENTS
- IDLE SPEED
- THROTTLE CABLE
- CLOSED THROTTLE AND IDLE ACTUATOR RESET
- IGNITION TIMING
- REPAIR PROCEDURES
- ENGINE CONTROL MODULE (ECM)
- MULTI-PURPOSE ELECTRONIC MODULE (MPEM)
- FUEL INJECTOR
- THROTTLE BODY
- THROTTLE POSITION SENSOR (TPS)
- IDLE BYPASS VALVE
- CRANKSHAFT POSITION SENSOR ICPS)
- CAMSHAFT POSITION SENSOR (CAPS)
- MANIFOLD AIR TEMPERATURE SENSOR (MATS)
- COOLANT TEMPERATURE SENSOR (CTS)
- MANIFOLD AIR PRESSURE SENSOR (MAPS)
- EXHAUST GAS TEMPERATURE SENSOR (EGTS)
- KNOCK SENSOR (KS)
- OIL PRESSURE SENSOR IOPS)
- TOPS SWITCH
- 05FUEL SYSTEM
- 01 - FUEL TANK AND FUEL PUMP
- GENERAL
- INSPECTION
- FUEL SYSTEM LEAK TEST
- FUEL PUMP PRESSURE TEST
- PROCEDURES
- FUEL HOSES AND OETIKER CLAMPS
- FUEL FILTER
- FUEL TANK
- FUEL PUMP
- 06ELECTRICAL SYSTEM
- 01- IGNITION SYSTEM
- GENERAL
- PROCEDURES
- IGNITION COIL
- SPARKPLUGS
- 02- CHARGING SYSTEM
- GENERAL
- TESTING PROCEDURE
- RECTIFIER/REGULATOR
- STATOR
- BATTERY
- 03- STARTING SYSTEM
- GENERAL
- TEST
- ELECTRICAL CABLES OR CONNECTIONS
- FUSE
- ENGINE CONTROL MODULE (ECM)
- ENGINE START/STOP SWITCH
- SOLENOID
- PARTS REPLACEMENT
- STARTER
- STARTER GEAR
- 04- DIGITALLY ENCODED SECURITY SYSTEM (DESS)
- GENERAL
- KEY PROGRAMMING
- TROUBLESHOOTING
- 05- GAUGE SENSORS AND FUSES
- GENERAL
- FUSES
- INFORMATION CENTER
- PROCEDURES
- INFORMATION CENTER
- FUEL BAFFLE PICK-UP SENDER
- WATER TEMPERATURE SENSOR
- COMPASS
- SPEED SENSOR
- DEPTH GAUGE
- 07PROPULSION
- 01 - JET PUMP
- GENERAL
- INSPECTION
- IMPELLER CONDITION262
- IMPELLER/WEAR RING CLEARANCE
- LEAK TEST
- PROCEDURES
- SACRIFICIAL ANODE
- VENTURI
- JET PUMP HOUSING
- IMPELLER COVER
- IMPELLER
- WEAR RING
- IMPELLER SHAFT AND BEARING
- 02- DRIVE SYSTEM
- GENERAL
- MAINTENANCE
- CORROSION PROTECTION
- PROCEDURES
- DRIVE SHAFT
- BOOT
- CARBON RING
- 03- REVERSE SYSTEM
- GENERAL
- PROCEDURES
- REVERSE CABLE
- REVERSE CABLE LEVER
- SHIFT LEVER
- REVERSE CABLE SUPPORT
- SHIFT LEVER HOUSING
- REVERSE GATE
- PIVOT SUPPORT
- LINK ROD
- PIVOT TRIANGLE
- PIVOT ARM
- 04- VARIABLE TRIM SYSTEM
- GENERAL
- TEST
- SWITCH
- MOTOR
- CONTROL MODULE
- PROCEDURES
- CONTROL MODULE AND MOTOR
- 08STEERING SYSTEM
- 01 - STEERING SYSTEM
- GENERAL
- ADJUSTMENT
- STEERING ALIGNMENT
- PROCEDURES
- NOZZLE
- HANDLEBAR GRIP
- STEERING COVER
- STEERING PADDING
- HANDLEBAR
- STEERING CABLE SUPPORT
- STEERING SUPPORT
- STEERING STEM
- HANDLEBAR SUPPORT
- STEERING CABLE
- 02- OFF-POWER ASSISTED STEERING (OPAS)
- GENERAL
- PROCEDURES
- FILTER
- VALVE
- WATER HOSE
- SIDE VANE
- CYLINDER SUPPORT
- TIE ROD
- SEALED TUBE
- CROSS SUPPORT PLATE
- 09HULL/BODY
- 01- ADJUSTMENT AND REPAIR
- GENERAL
- PARTS REPLACEMENT
- DECALS
- GLOVE BOX
- SEAT
- REMOVABLE SEAT COWLING
- SEAT COVER
- SEAT LATCH
- ENGINE COVER
- STORAGE COMPARTMENT COVER5
- STORAGE COMPARTMENT COVER HINGE
- STORAGE COMPARTMENT COVER SHOCK
- STORAGE COMPARTMENT COVER LATCH
- STORAGE COMPARTMENT COVER INNER SHELL
- FRONT GRILL OF COMPARTMENT COVER
- ACCESS COVER
- CONSOLE
- MIRROR
- DEFLECTOR AND/OR UPPER GRID
- SIDE MOLDING
- INLET GRATE
- RIDING PLATE
- JET PUMP SUPPORT
- THRU-HULL FITTING
- BUMPER
- WAKE PYLON
- SPONSON
- SPONSON ADAPTOR
- DRAIN PLUG
- CARPET
- CLEANING
- SEAT
- BODY AND HULL
- CARPET
- REPAIR
- HULL AND BODY
- TOOLS AND MATERIALS LIST
- 10TECHNICAL SPECIFICATIONS
- 01- GTI AND GTI SE
- 02- GTX AND GTX WAKE
- 03 - GTX SUPERCHARGED AND GTX LIMITED
- 04- RXP AND RXT MODELS
- 11ELECTRICAL CONNECTORS AND WIRING DIAGRAM
- 01 - ELECTRICAL CONNECTORS
- DEUTSCH CONNECTORS
- PACKARD CONNECTOR
- AMP CONNECTOR
- ECM CONNECTORS
- BATTERY AND STARTER CABLE TERMINALS
- 02- WIRING DIAGRAM
- WIRE COLOR CODES
- WIRE DIGIT CODES